Processing Parameter Settings Recommended for Common Materials

Article author
Admin
  • Updated
The processing parameter settings recommended on this page are based on laboratory tests. The processing results may vary according to the material manufacturer and ambient environment. Before processing, you are advised to test your material to obtain the settings for your expected processing results.
The parameters for each processing type include power, speed, and pass (number of engraving or cutting times). For bitmap engraving, you can also see bitmap mode and lines per cm. For example, the value 100%-1200mm/s-1 indicates that you are advised to set the power to 100%, speed to 1200 mm/s, and pass to 1. The value 90%-2400mm/s-220 lines per cm-1 indicate that you are advised to set the power to 90%, speed to 2400 mm/s, lines per cm to 220, and pass to 1.
 
Material Name
Machine
Processing Parameters
   
Score
Vector Engrave
Bitmap Engrave
Laser Cut
Art Scratch Paper
F1 10W
100%-1200mm/s-1
90%-2400mm/s-220 lines per cm-1
   
3.5mm Corrugated Paper
F1 10W
70%-110mm/s-1
50%-300mm/s-100 lines per cm-1
40%-300μs-300DPI-Jarvis-1
 
3mm Basswood
F1 10W
70%-80mm/s-1
100%-300mm/s
100 lines per cm-1
80%-420μs-270DPI-Jarvis-1
90%-3mm/s-1
Silver-Black Leather for Engraving
F1 10W
90%-500mm/s-1
70%-500mm/s-120 lines per cm-1
 
90%-10mm/s-1
Black Metal Name Card
F1 10W
100%-400mm/s-1
100%-400mm/s
160 lines per cm-1
   
Black Alumina Sheet
F1 10W
90%-1100mm/s-1
90%-1100mm/s
300 lines per cm-1
   
3mm Black Acrylic
F1 10W      
100%-2mm/s-1
Rock Coaster
F1 10W
100%-200mm/s-1
100%-500mm/s
90 lines per cm-1
   
Art Scratch Paper
F1 2W
90%-1650mm/s-1
60%-1700mm/s-220 lines per cm-1
50%-200μs-400DPI-Jarvis-Invert-1
 
Brass F1 2W
80%-300mm/s-1
100%-300mm/s-200 lines per cm-1
80%-200μs-550DPI-Jarvis-Invert-1
 
Red Copper
F1 2W
100%-10mm/s-1
100%-3mm/s-200 lines per cm-1
   
Aluminum Sheet
F1 2W
90%-350mm/s-1
100%-600mm/s-200 line per cm-1
60%-200μs-550DPI-Jarvis-Invert-1
 
Gilded Material
F1 2W
100%-10mm/s-1
100%-5mm/s-200 lines per cm-1
   
Silver
F1 2W
100%-10mm/s-1
100%-5mm/s-200 lines per cm-1
   
Black Metal Name Card
F1 2W
90%-650mm/s-1
100%-650mm/s-220 lines per cm
-1
60%-150μs-750DPI-Jarvis-Invert-1
 
Black Alumina Sheet
F1 2W
80%-800mm/s-1
90%-500mm/s-200 lines per cm-1
70%-150μs-500DPI-Jarvis-Invert-1
 
Stainless Steel
F1 2W
80%-25mm/s-1
50%-550mm/s-200line per cm
-1
60%-150μs-450DPI-Jarvis-Invert-1
 
3mm Black Acrylic
F1 2W
80%-60mm/s-1
90%-200mm/s-200 lines per cm-1
85%-200μs-550DPI-Jarvis-Invert-1
 
Rock Coaster
 
F1 2W
100%-50mm/s-1
100%-100mm/s-240 lines per cm-1
90%-150μs-450DPI-Jarvis-Invert-1
 
3mm Basswood
F1 10W+Slide Extension
70%-160mm/s-1
35%-110mm/s-100 lines per cm-1
70%-370μs-250DPI-Jarvis-1
 
Art Scratch Paper
F1 10W+Slide Extension
20%-160mm/s-1
 
 
 
Silver-Black Leather for Engraving
F1 10W+Slide Extension
20%-130mm/s-1
 
 
 
3.5mm Corrugated Paper
F1 10W+Slide Extension
40%-110mm/s-1
40%-130mm/s-100 lines per cm-1
40%-300μs-300DPI-Jarvis-1
 
Art Scratch Paper
F1 2W+Slide Extension
40%-160mm/s-1
 
50%-150μs-450DPI-Jarvis-Invert-1
 
Rock Coaster
F1 2W+Slide Extension
80%-130mm/s-1
 
90%-220μs-450DPI-Jarvis-Invert-1
 
Black Metal Name Card
F1 2W+Slide Extension
50%-160mm/s-1
 
60%-150μs-450DPI-Jarvis-Invert-1
 
Black Alumina Sheet
F1 2W+Slide Extension
80%-150mm/s-1
 
50%-150μs-600DPI-Jarvis-Invetr-1
 
Stainless Steel
F1 2W+Slide Extension
80%-150mm/s-1
 
50%-150μs-450DPI-Jarvis-Invert-1
 
3mm Black Acrylic
F1 2W+Slide Extension
80%-160mm/s-1
 
85%-200μs-550DPI-Jarvis-Invert-1
 
Brass
F1 2W+Slide Extension
90%-160mm/s-1
50%-150mm/s-200 lines per cm-1
80%-200μs-550DPI-Jarvis-Invert-1
 
Alumina Sheet
F1 2W+Slide Extension
80%-150mm/s-1
80%-160mm/s-200 lines per cm-1
60%-200μs-550DPI-Jarvis-Invert-1
 

Was this article helpful?

10 out of 11 found this helpful

Have more questions?

Comments

0 comments

Article is closed for comments.